Page 9 of 9
Re: Triple Procedure & Setup (Costs around 80USD)
Posted: Fri Jun 25, 2021 3:43 pm
by Raffli16
I know this is an old discussion but new owner and want to perform this procedure. But how does one go about getting the drivers for the mut-3 software. I saw in an older post about sending money to a PayPal account.
Re: Triple Procedure & Setup (Costs around 80USD)
Posted: Wed Jun 30, 2021 7:35 am
by kpetrov
Raffli16 wrote: ↑Fri Jun 25, 2021 3:43 pm
I know this is an old discussion but new owner and want to perform this procedure. But how does one go about getting the drivers for the mut-3 software. I saw in an older post about sending money to a PayPal account.
Write to this guy:
https://www.facebook.com/people/Nikolay ... 317961322/
Re: Triple Procedure & Setup (Costs around 80USD)
Posted: Mon Oct 10, 2022 3:54 am
by mohinder
Hi
I prepared a short movie as an instruction.
https://www.youtube.com/watch?v=nuH6ct2zdH4
Re: Triple Procedure & Setup (Costs around 80USD)
Posted: Mon Sep 11, 2023 10:34 pm
by CharlieMac
Now I'm stuck. My car is in its charging phase of the DBCAM. What happens if I turn on the car to wind up the window?
EDIT: I found the drivers. The seller finally gave me a straight answer among the bucketloads of software they supplied. The file was openport2_setup_1004341.exe
I'm a bit stuck finding the drivers that came with my device (as in step 3). The Aliexpress seller has supplied so many different pieces of software but nothing that looks like basic drivers.
The closest thing I found to a driver was "mini vic driver for toyota.msi". Will that work? Does anyone have a link to the correct drivers for the "Inc. OpenPort 2.0 REV E 1234"?
The description of my plug is "Full Chip Openport 2.0 ECU FLASH open port 2 0 Auto Chip Tuning OBD 2 OBD2 Car Diagnostic Tool For Mercedes Benz J2534 Scanner" btw. It has 320 reviews so you can tell if it the one I've got.
Re: Triple Procedure & Setup (Costs around 80USD)
Posted: Wed Sep 13, 2023 5:36 am
by kpetrov
CharlieMac wrote: ↑Mon Sep 11, 2023 10:34 pm
Now I'm stuck. My car is in its charging phase of the DBCAM. What happens if I turn on the car to wind up the window?
EDIT: I found the drivers. The seller finally gave me a straight answer among the bucketloads of software they supplied. The file was openport2_setup_1004341.exe
I'm a bit stuck finding the drivers that came with my device (as in step 3). The Aliexpress seller has supplied so many different pieces of software but nothing that looks like basic drivers.
The closest thing I found to a driver was "mini vic driver for toyota.msi". Will that work? Does anyone have a link to the correct drivers for the "Inc. OpenPort 2.0 REV E 1234"?
The description of my plug is "Full Chip Openport 2.0 ECU FLASH open port 2 0 Auto Chip Tuning OBD 2 OBD2 Car Diagnostic Tool For Mercedes Benz J2534 Scanner" btw. It has 320 reviews so you can tell if it the one I've got.
You can use the original driver from tactrix website.
https://www.tactrix.com/index.php?optio ... &Itemid=61
Regarding the window down during the procedure I made the same mistake. I don't remember exactly what happened after I have turn it on to close it... rather it continued or I started the procedure again but it didn't take any extra time, unless your vehicle has been charging for long.
Re: Triple Procedure & Setup (Costs around 80USD)
Posted: Wed Sep 13, 2023 5:39 am
by kpetrov
mohinder wrote: ↑Mon Oct 10, 2022 3:54 am
Hi
I prepared a short movie as an instruction.
There are few steps missing in the video.
After the BMU reset one have to manually enter the battery age and vehicle mileage before proceeding with DBCAM.